Jump to content
308AR.com Community
  • Visit Aero Precision
  • Visit Brownells
  • Visit EuroOptic
  • Visit Site
  • Visit Beachin Tactical
  • Visit Rainier Arms
  • Visit Ballistic Advantage
  • Visit Palmetto State Armory
  • Visit Cabelas
  • Visit Sportsmans Guide
OldGregg

Mag catch channel issue

Recommended Posts

So a while back I purchased a upper lower combo form a local vendor and it sat in the safe for a while. I recently started to build this thing putting it together and I have the lower all but finished, I install the the mag catch and button and am function testing it and I notice that the magazines will pop out if tapped on the side of the magazine and if the magazine is loaded they will literally fall out from shaking the gun. I noticed that the mag catch sits out proud of the receiver by about.030 and the part of the catch that is supposed to engage the magazine barely touches it and the catch is screwed down as tight as it can go. Its actually other wise a very nice upper lower combo aside from this issue so my question is if anyone knows if there is a local machinist in Washington state that  would be able to machine out some material of the mag catch channel so it can sit flush and engage the magazines better. I've tried several different magazines and mag catches and the only one that doesn't drop completely free are P mags but it appears that the catch is just catching on the polymer and digging in to the magazine and I don't typically use P mags anyway. Any advice for a relatively new AR 308 builder?

Share this post


Link to post
Share on other sites

If it isn't an out of spec lower then possibly an Armalite AR-10 mag catch would help. As described in this thread they have a deeper engagement surface on the magazine. 

 

Share this post


Link to post
Share on other sites
6 hours ago, OldGregg said:

I noticed that the mag catch sits out proud of the receiver by about.030 and the part of the catch that is supposed to engage the magazine barely touches it and the catch is screwed down as tight as it can go

Are you positive of this, it's in as far as it will go?   Push in on the mag catch button with a punch (or an ink pen, whatever is handy) and push that button in even further than you could with your finger.  You'll be able to get another couple rotations on that mag catch that way, and tighten it up more.  More spring pressure (preload) on the spring, deeper sitting mag catch to grab the mags better.

Share this post


Link to post
Share on other sites

pull the bolt catch off and you can get even another turn on it.

We are in WA and love experimenting/ improving/ruining other people's slides, barrels, receivers or any thing else they want run through a mill!

Like the commercial says, we are just OK!

Where in WA?

Share this post


Link to post
Share on other sites
12 minutes ago, Albroswift said:

pull the bolt catch off and you can get even another turn on it.

 

You won't have to remove the bolt catch, if you use a punch/pen/whatever to bottom that button, and coil-bind that spring.  You'll be able to get all the rotation that you'd need that way, even with an AR15 catch in a .308AR.   :thumbup:

Share this post


Link to post
Share on other sites

Sorry about the lateness of my reply but answer some questions:

Jtallen83: I'm familiar with the catch you're talking about and it is not the length of the rod that is the problem as much as how deep the channel is and how much of the surface of the actual catch that can engage the magazine.

98Z5V: I have tightened the catch down as many twists as it will go. I pushed the button in as far as possible and tightened it till it would no longer clear the the outside of the lower while twisting and I am still encountering this problem.

Albroswift: I might have to take you up on that if this can't be remedied by what hopefully is my ineptness at building this thing. I am in Seattle down in the city.

Beltfed: Thank you, I searched but for some reason was not able to find this article

Share this post


Link to post
Share on other sites

I hope this is helpful to anyone to give a perspective of how far out it sticks. If any other angles are helpful please let me know. This pic btw is resting with the mag release button not depressed at all.

IMG_1558.JPG

Edited by OldGregg

Share this post


Link to post
Share on other sites

I'm in the city as well, shoot at the Seattle Police Athletic Association (SPAA) just south of the Boeing field 

We should throw some lead down range some weekend 

Mill is in Orting. 

Photo: looks like it needs a few more twists for sure.

 

Share this post


Link to post
Share on other sites

Almost finished the build around the ported sig 5.56 barrel.

Dabbed a little 44/40 original cold blue in the ports 

Anderson upper and lower

Toolcraft BCG

Not sure where the tiny little millspec looking buttstock came from, been laying around for 20 years or so. 

MBUS sights only at this time

Aim Sport guard, I was impressed with this, self aligning, lightweight, clean looking.

Didn't have a buffer detent spring or pin, the rule that if you dig deep enough in the parts bin you will find what you need didn't quite work out, stuffed the spring and buffer in it anyway and snapped her shut. 

Parts bin almost empty. 

Range in the morning with this and the 308 and and...

 

20190822_184201.thumb.jpg.522aaf1fdb431a61b07a7599cf47d8ca.jpg

 

20190822_184208.thumb.jpg.d71c9da198f3608a72cf4ba99f8e6d86.jpg

 

20190822_184156.thumb.jpg.3c90d7edf3cc01650821d05995025277.jpg

 

 

Edited by Albroswift

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...