Jump to content
308AR.com Community
  • Visit Aero Precision
  • Visit Brownells
  • Visit EuroOptic
  • Visit Site
  • Visit Beachin Tactical
  • Visit Rainier Arms
  • Visit Ballistic Advantage
  • Visit Palmetto State Armory
  • Visit Cabelas
  • Visit Sportsmans Guide

Recommended Posts

Posted

I'm putting together a rifle on the AR-10 platform, to get a cheap, semi-auto rifle that can be accurate at long range. For hunting and range. I bought an assembled, DPMS v1 upper from gunbroker with a Ballistic Advantage 20" barrel. I have a Daytona Tactical 80% lower, not my first 80% and while it's not perfect the holes round and in the right place.

I'm going to kind of blog the experience of getting it to run smooth like it should. I'll be grateful if anyone chimes in with their knowledge.

First time I tried it out I bought a 5-round steel mag online (for hunting in Florida, max is 5-rounds) and a 25-rd pmag with a window from Bass Pro. I got some nice 168gr soft point and some 15-gr "target and practice" winchester 7.62 in the white box.

With the 168gr and the steel mag it's great already. With the practice ammo and the plastic mag, a couple issues:

 - Light strikes every few rounds

 - bolt-over-cartridge failure to feed.

 - The upper and lower are kind of "loose" with each other to the point that if I shake/smack it a bit the bolt catch will release without being pressed.

So then I bought a triggertech duty 3.5lb AR-10 trigger to try and help with the light strikes, a firing pin from PSA, and a stripped upper from Daytona. I did some shimming around the rear takedown pin like many people have suggested and that did help some but there's still more gap than I'd like to see, so next I will try the upper from the same company. I haven't tested this yet because, when I installed the cartridge trigger, I found that the "disconnect" action doesn't work right. The triggertech trigger doesn't have a disconnect part exactly but I mean, whatever mechanism catches the hammer on the way back if the trigger is held down.

With the triggertech trigger installed, if I hold down the trigger, pull and release the charging handle, release the trigger, it won't go "click". This is hammer follow. I have not really fixed it but I found that when I take the rear takedown pin out, hold the upper and lower together manually, so they are tighter this way than with the takedown pin in, holding down the trigger and pulling the charging handle will reliably catch and retain the hammer.

So I there's something like a few degrees angle between the point on the hammer backswing where the trigger sear would catch the hammer if it were released, and the point where the disconnect will catch it if the trigger is depressed. This angle is slightly larger or slightly further back on the triggertech trigger than the standard FCG. That, plus the fact that the BCG-to-upper distance (see below) is a bit large on this random gunbroker upper receiver, is a classic tolerance stacking issue.

I found some really good posts on this forum already that are helping me think through the issues this thing might have so I'll link them in the thread.

Posted

DIMENSIONS

I thought maybe I drilled the trigger/hammer pins too low, leading to the hammer follow condition, but my dimensions are in line with those shown:

 

Posted (edited)

BCG-to-Upper I would have never thought to measure this until I saw the post below. The two uppers I have differ in this measurement so now I think switching them will help. "BCG too high above lower receiver" would make perfect sense for both failure to feed and the hammer interaction issue.

He also mentions the distance from mag catch to top of lower and it looks like his is a bit far while mine is 0.66 which is right about where it should be.
 

 

Screenshot From 2026-11-17 21-59-05.png

Edited by 308aruser
Posted
36 minutes ago, 308aruser said:

BCG-to-Upper I would have never thought to measure this until I saw the post below. The two uppers I have differ in this measurement so now I think switching them will help. "BCG too high above lower receiver" would make perfect sense for both failure to feed and the hammer interaction issue.

He also mentions the distance from mag catch to top of lower and it looks like his is a bit far while mine is 0.66 which is right about where it should be.
 

 

Screenshot From 2026-11-17 21-59-05.png

To check, I took the Daytona upper with just the BCG and charging handle no barrel etc, and attached that to the Daytona lower with the takedown pins. With a little bit of soda can in the upper's takedown hole it is nice and snug but it still doesn't push the Triggertech hammer back far enough to capture it when the trigger is depressed. Again, when I take out the rear takedown pin and press the upper+lower together tightly, the "disconnect" action works like it should.

I'm reaching out to the company to see if I can get a better fit and also looking into other ways to attach the upper.

Posted
2 minutes ago, Belt Fed said:

I have a Radical 308 that is the same as yours. mag does not go high enough for the bolt to catch the round well.

Yes I get you, it's a finicky platform for sure. it appears this upper+bolt carrier are too high above the lower because it gets fail-to-feed issues and also doesn't press the hammer back far enough to catch it when the trigger is depressed. The magazine catch placement is where it should be.

Posted

This radical is really poorly made, supposed to be billet upper and lower. the upper looks like something i would do. this picture shows chatter marks but it's worse than the pic shows.

 

20261115_1421031.thumb.jpg.8f4a23277a70b66671ebc26644377ea3.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...