TacBlade

Good Queation? I never ever asked, I just assumed they had them on hand. I guess I will have to call them back?

So do I just eyeball it and hope the hole on the gas block and the hole in the barrel line up when I put the gas block on? I have no marks or indentions on the barrel to go by?

It was mentioned to me that the Fulton Armory Bolt Carrier is just a Chrome DPMS carrier from DPMS. You can get a standard Chrome Carrier from DPMS. Someone correct me here if I am wrong or was given the wrong info?

BAM!!!!!!!! I just ordered the JP Bolt and Bolt Carrier Group!!!! They told me to get the full benifit of the Low Mass Bolt Carrier, was to use an Adjustable Gas Block and lower the Gas needed to push it back and that will reduce felt recoil...I don't have an adjustable one right now, but I am going to fire mine without one and switch it over to an adjustable one to see what the difference is.

You have to use their Bolt, if you use their Bolt carrier. You do not have to use their Spring and Buffer. But you can use their upgraded Bolt in any DPMS style Bolt Carrier. I believe that is why Brownells now sells their Bolt by itself, so you can use it in your Bolt carrier. It may very well, not work as good without their spring and buffer though. I think I will give them a call before I go and buy one and see what they have to say.

What is your thoughts on the JP Bolt Group? I am thinking of picking one up for this build? I think the finish is much better than any others out there for wear and tear? As far as the low mass part, it may lessen the felt recoil and adding that to my "HeavyBuffer" setup I have coming, it may make a difference? What do you think?

It is 1/16" Is that the standard size?

I thought I had better add to this post that the Kaiser barrel does work with the DPMS as you can tell from my other post.

Should I measure it? I do not have the Gas Block on yet? It is smaller then the hole in the Gas Block?

I got my Larue Gas Block, Kaiser 16" Barrel with Mid length Gas tube, Smith Enterprise Flash Hider. I am putting it all together today and should have some pics up tomorrow. I still have to figure out if the JP Bolt group is worth the money. It says it calms the felt recoil with their buffer, but not sure without the buffer. I have one of the HeavyBuffers with a spring coming also. Its all finally coming together. Also, I have to get a mount and a scope or just shoot it with my flip up sites for now. I will get the pics up tomorrow though...Thanks!!! I have to go watch the Steelers kick some ass right now!!!

Are those pretty much like the DPMS ones? What about the chrome one from DPMS, is it better and also Fulton Armory?

How about I get one and then you will?

Is the JP Enterprises a better bolt carrier group or is it just more expensive? Fulton Armorey? DPMS? Who else makes them out there, that you can get right now? I need one right now? Thanks!!!

I just found something that stated their rifles take AR10 mags, so that says they are AR10 compatible. >:(

I looked all over the place and even on their website and no info about what style they make their barrels for?

Hey! There are no stupid questions! I have been into guns my whole life and I would like to know the same thing, as I am building one right now. I just cannot figure out to go with 16" or 18" either, and what the effect is going to be with going with a carbine gas tube rather than a Mid or full length gas tube? I need answers also. Thanks

Here are a few for you. There are alot more. Let me know if you need more. Have a Good One!!!! http://www.arizonacustomknives.com/ http://www.knifeart.com/ http://www.knivesshipfree.com/ http://www.onestopknifeshop.com/ http://www.steeladdictionknives.com/store/

That top one will cost you $1500.00 and all four of those are made by Busse

I can keep going!

I got mine and it has alot of gear in there! But, you will be disapointed about not having very many .308 AR items >:( But, I have figured out a solution to this!!! I was told to call the guy in Marketing, forgot his name, but he is the only one, and ask him if he was planning on adding anymore items relating to the .308 AR. I gave him a call and he said he was working on it and would like to have anyone that could give him some insight on what he should be putting in the catalog to CALL HIM!!!!! So, give Brownells a call and ask for the guy in MARKETING and let him know what we want. I gave him my insight, but I am sure you guys have alot more input that I have. Have a good one!!!

This is a Large Sebenza Classic, customized by Tom Mayo and Tom Krein! These are about as good as it gets for a Production Folder!!! Its also for sale!! Yep, got to fund a new .308 AR project!!

Great looking car and would like to chat with you anytime!!!

Can I use an AR10 Barrel on a DPMS upper. I have a DPMS barrel nut, I am just wondering about the barrel. Thanks...

I added pics with my IMOD and MIAD and Magpul Rails.

That is a great idea! I will be doing that to mine. Also, my selector switch turns from safe to fire and back, very hard? It looks like the surface of the selector switch where the pin rides is very rough and the pin tip is kind of chewed up. Should I replace both of these? It works fine, but is hard to turn?