imschur

No wind is going to be a match for unforgiven. Glad your ok

Well if all goes well I will throw this thing together tomorrow. I have everything but the buttstock and sights. Im getting mixed reports in when the magpul moe rifle stock will start shipping. I may use the Wilson rogers Super Stoc instead.

Thought I would give one of the MOE+ a try. Tom's influence is pretty obvious

Here it is. I might be getting a good deal on a few more 51T muzzle devices soon.

For my 300 Blackout build I decided to skip the Young MFG bcg's I normally purchase and give this Wilson Combat NP3 Coated Bolt Carrier Group a shot. This is my first NP3 coated part. Pretty slick stuff. The BCG appears to be machined pretty clean.

<laughs>

I think it's to safe to say there are bad experiences for folks with all companies. No companies products and services are infallible. Lets stick to the question of warranties as asked in the original post. Customer service and service after the sale is a whole other ball of wax.

jeez they cashed my checks instantly

It was one week shy of 6 months that they sent them back. How far along are you?

My form 4's are back in route to the BATFE

Well i had originally good experiences with Para when they were in Canada. Last years LDA does not work and they will not acknowledge the form i have filled out. I believe they are now under new ownership, Freedom Group. Maybe I have slim hope for resolution Ruger screwed me good. Sent in my Redhawk for a new barrel. The kind with the notches for scope rings. They butchered the top strap, then denied they did it. Got obnoxious and blamed me. That was Bill Ruger SR days. Maybe things changed with him dead Krieger as in Accu Rails made good on a hack job by another licensed gunsmith installing his system

i just checked, tannerite again. Please pass along it along if you see it again

Yes the threads are slightly conforming to each other

no but not tight enough will

jlaw the typical barrel nut tightening is done three times tightening. Tighten the nut pretty snug then back it off Tighten it again approaching the notch where you plan on stopping. Back it off again Tighten the final time on the desired notch. You will be surprised how much incrementally further the nut goes with each torquing

Federal 147 grain Hi-Shok JHP Hollow Point 9MS - 1000 rounds

Those are the two part tannerite. I think the kind Im refering to was black powder or something. They were like a 2" cap for a cap gun

Anyone remember these? They were like a 2x2 piece of foam with a red bullseye on them. Even an arrow or airgun would set them off.

Well my attorney is arguing with the BATFE. He has told me to do as they request as to not risk my applications. He is arguing on principle for the applications that follow. The investigator is going to her superiors for guidance.

My 9mm will be FDE too. Roger has FDE levers... >:(

This is pretty interesting. A 22-250 in a mostly AR-15 sized lower. AR-15 Specifications Receiver Material 7075 T6 Aluminum Forged Receivers Machined By Olympic Arms Receiver Finish Black Matte Anodized Receivers, Parkerized Steel Parts Action Gas Operated Semi-automatic Action Upper Type Flat top w/ picatinny rails Front Sight Gas block w/ picatinny rails Handguard Predator FIRSH Barrel 24” Heavy match grade bull barrel, 416 stainless steel Chambering .22-250 REM;.223 WSSM, .243 WSSM, .25 WSSM, .300 OSSM Bore Long-life non-chromed bore Twist Rate .22-250 REM (1x14) .223 WSSM (1x14) .243 WSSM (1x10) .25 WSSM (1x10) .300 OSSM (1x12) Muzzle Crown Stock ACE FX Skeleton Stock The Only AR-15 that can be chambered in .22-250 Rem. The UMAR utilizes an extended length magazine well to accomodate the UMAR magazine allowing shooters the ability to utilize longer COL loads. This is especially applicable to the WSSM cartridges when wanting to load heavier bullets. This proprietary lower design still accepts MIL Spec upper receivers or various calibers and their appropriate magazines. The UMAR comes with one 5 round caliber specific custom magazine that will either fit the .22-250 or the WSSM/OSSM cartridge 24" SS Bull Barrel* Fluting available for additional cost Picatinny flat-top upper Olympic Arms Predator Style handguard A2 buttstock Optional ACE skeleton stock (shown in picture) Your choice of side-sling mount or bi-pod mount 5 round billet aluminum magazine *Bull barrel standard on the UMAR for the WSSM & OSSM cartridges are 416 SS precision broach-cut barrels. All .22-250 caliber UMAR rifles use 416 SS button rifled barrels.

I recall as I was ordering FDE rail covers, MOE+ pistol grip and the Super Stoc a thought went through my mind "Fucking Tom and FDE"

congrats man

two actually..very soon

you cant imagine what my coffee table looks like at the moment. Three of everything <laughs>