6132expert

I will have to always remember this tactic.

Got ya, so when you talk about timing the barrel nut to fit a handguard is just because the barrel nut fit in such a way that the handguard did not fit properly? I still have much to learn.

[img width=810 height=604]http://i1128.photobucket.com/albums/m494/ajh2004/44a589a0.jpg [img width=810 height=604]http://i1128.photobucket.com/albums/m494/ajh2004/19e6ffe4.jpg [img width=810 height=604]http://i1128.photobucket.com/albums/m494/ajh2004/63e12f5e.jpg [img width=810 height=604]http://i1128.photobucket.com/albums/m494/ajh2004/e8e862f0.jpg [img width=810 height=604]http://i1128.photobucket.com/albums/m494/ajh2004/dbc4f45b.jpg [img width=810 height=604]http://i1128.photobucket.com/albums/m494/ajh2004/70b52f84.jpg [img width=810 height=604]http://i1128.photobucket.com/albums/m494/ajh2004/e5af09b6.jpg [img width=810 height=604]http://i1128.photobucket.com/albums/m494/ajh2004/74cb09cc.jpg Sorry if they are a little fuzzy. It was with cell phone. I may be able to get better when I go to the range. What we have is, is a AAS Lower / Multi Cal RRA single stage trigger LPK Over sized selector Brownells lazer etched upper Brownells ( dont tread on me ) dust cover Brownells lazer etched ( American Flag ) take down pin and mag release Tear drop forward assist Magpul Moe, Moe grip, Winter trigger guard, XTM panels,AFG2, and Mbus Gen 2 sights RRA BCG and CH YHM quad rail With end cap CMMG 16 inch carbine lenght CMMG single rail gas block unknown muzzle break

Well even if I did take some off it would of made things a hell of a lot easier. Now what the heck is all this talk about timing? Is it something I am suppose to be doing?

I noticed you saying you was getting you MB timed in another thread. What does this do? Why is it done?

Thanks for the info I will remember it for sure! I got it, I went out to my shop and looked around and I came across an old wooden vise so I took a paddle bit and cut me a 5/8 hole glued in some plumbing rubber gasket material and clamped the barrel down then moved it to the vise. I then took and tightened and loosened several times and had little luck then all of a sudden I very very slowly tightened the break untill I had it right. I did sctratch the break up a little from the wrench being taken on and off. I will load pictures in a few. Also I should have my ammo by the 15th so I hope the Range is ready for me.

I have no block vice. I am going to make one out of some wood and rubber. Also I understand then tighten and loosen sstem, but would I be better off using a shim set to get it exactly where I want it?

OK guys, I have now my first problem with my build. I am down to the final assy and the damn crush washer is giving my trouble. I will try to load a picture later , but for now here is my problem. The break I have allows the flash and excess whatever to go out the sides and on the upper ( or lower side) there are 2 small holes I want them at the top s if ever in the prone dust is not blowing up and the muzzle is staying down. The washers I got from brownells and it was the thinner of the 2 I saw. How much pressure does it take to crush the washer? All I need is a 1/4 of a turn to get the break where I wnt it.

http://www.bradswarehouse.com/ Have tried this place. They have a lot for the 300AAC

I dont know. I do know I looked almost everywhere and nobody had it.

Guys it is 1833 EST and MidwayUSA has 300 BLK ammo in stock ( rem 220 gr) I just ordered 3 boxes. Oh yeah use promotion code 100811126 for 10 bucks off 50 581175 for 50 bucks off 500 <thumbsup>

My thought ecactly! <laughs>

Thats why they go under the pillow

<lmao> <lmao> <lmao> <lmao> <lmao> <lmao> <lmao> <lmao> You said go shoot your stick <laughs>

I just emailed the perpitrator that was put in office for my district. I would suggest you do the same!

I know your pain! I had my first hand gun stolen. It was a Ruger P89 45 that was almost 20 years ago and I still get a letter from the county that they are still looking for it. I do not have the serial number on hand right now , but I am going to get it from the Sheriffis dept and run it on this site. I to have gotten smarter and now keep a detailed record of all firearms in the fileing.

For everyone looking for ammo. ammonow.com has remington 220 in stock showing.

Also there is hornady 208 amax 300 whisper

Well if you look like any of the rest of us on here you better dress her up REAL nice!! <lmao>

tHEN YOU SHOULD BE HAPPY TO KNOW i FOUND THIS Reply Knight's Armament Administrator says: June 11, 2011 at 08:08 Barry, first off thank you for your interest in our product, and to be honest they are already available to the public. Our shopping area has not been updated so I apologize for any issues concerning purchasing them. If you contact our Commercial Sales Department they will gladly help you. Do not quote me but I believe the sights are approximately $150.00 a piece. My question is going to be can they be placed on eather side of the rifle with no issues for left and right handed shooters. I do like the idea of these sights but they are pricey to me.

How much higher would you need the scope to be for the gen 1s to fit? This will give me an idea when I figure out how much thinner the gen 2s are and if I need o get the 1.93. That would give me ruffly 3/8s inch high but I would prefer to have the lower profile mount.

Yall need to get some yhm anti-rotation screws. YHM-9434 I know I am picky..lol

Survial how far is the center axis of your scope from the rail? I am looking using the Larue spr 1.5 but I also am going to use the gen 2 magpul buis under the scope. I am now woundering if I need to use the spr 1.93

Where do I find the discount codes? Here? Also do you know of anyone whom may make a scope mount that will release and just hing over away from the ejection port?

will do for sure . thanks