Jump to content
308AR.com Community
  • Visit Aero Precision
  • Visit Brownells
  • Visit EuroOptic
  • Visit Site
  • Visit Beachin Tactical
  • Visit Rainier Arms
  • Visit Ballistic Advantage
  • Visit Palmetto State Armory
  • Visit Cabelas
  • Visit Sportsmans Guide

Matt.Cross

Peace Keeper
 View Profile  See their activity

  • Posts

    6,298

  • Joined

  • Last visited

 Content Type 

Everything posted by Matt.Cross

  1. Matt.Cross
    1:10 will stabilize anything, but after 300-400 yards lighter stuff will fall apart accuracy wise. The slower twist will keep the lighter stuff together out to about 500 yards and after that it'll be iffy.
  2. Matt.Cross
    Simply put, the reason is that those two twists suffice to stabilize a broad range of bullet weights without compromising anything. I prefer the 1:10 twist for stabilizing the heavier bullets at long ranges. The faster twist makes lighter bullets act more erratic sooner, but I don't shoot lighter bullets so it's not an issue.
  3. Matt.Cross
    That's fair enough IMHO.
  4. Matt.Cross
    Woo woo! Sexy!
  5. Matt.Cross
    Sig Sauer Kilo 3000BDX binoculars and a Kestrel 5700 weather meter.
  6. Matt.Cross
    When hand drilling the wood shaving indicate that you've gone far enough, basically preventing drilling a divot in the bottom of the bore. It is certain that a burr will be left at the bottom of the hole, but the first shot afterwards will expedite it's removal.
  7. Matt.Cross
    There's no need to ream it, drilling will suffice. People drill them by hand with a wooden dowel in the bore, a mill will make it 10x easier.
  8. Matt.Cross
  9. Matt.Cross
    I'm out on the Southwestern side of NC if you end up needing help in person.
  10. Matt.Cross
    Welcome to the forum!
  11. Matt.Cross
    I'm not falling victim to the rule!
  12. Matt.Cross
    Just out of curiosity, why the 18" rather than the 16"?
  13. Matt.Cross
    I don't know, but covering up the Adam's Apple with a scarf was brilliant!
  14. Matt.Cross
    Only if you're stone deaf, which you might be after Ron empties a mag or so.
  15. Matt.Cross
    The MA TEN is definitely not small frame.
  16. Matt.Cross
    Welcome from NC! What's your intended use? What kind of distances will you be shooting? Do you buy "cheap" ammo exclusively? These are some questions that could help us help you.
  17. Matt.Cross
    Welcome from NC! What part of WV? I used to work down on the KY border near Matewan.
  18. Matt.Cross
  19. Matt.Cross
    I bust your balls about it, but I'd probably do the same if I were in your shoes.
  20. Matt.Cross
    CA compliant guns of course, but guns nonetheless!!!
  21. Matt.Cross
    Exactly. Make the best of everything within your own domain.
  22. Matt.Cross
    No doubt in my mind we've moved far beyond the mark our kids, grandkids, or even great-grandkids will be responsible for paying. We're not headed for any pay-off, we're headed towards a buy-out. It sounds crazy, but it's no crazier than the decisions that have brought us to this point nationally.
  23. Matt.Cross
    I just wanted to come in here and express my love and appreciation for all the handout accepting bums in this country who finally got Uncle Sam to buy me a new MRAD, and ya'll are downing them!
  24. Matt.Cross
    Ehrmagerd!
  25. Matt.Cross
    Those two remaining screws are for wedging the rear of the handguard open so it can be pulled off the receiver. Tighten both screws a half turn in tandem until the handguard can be pulled away from the receiver.
×
×
  • Create New...