edgecrusher

No, do not drill anything yet. Check your post first

That is not it. Those measurements are for the size of the barrel diameter at the block. Measure your spring and buffer as well as the buffer weight and inner depth of buffer tube please and post.

I’m on season 2. You are absolutely right on the dub, and translation. I switched it to Spanish with subtitles. Far better

If you don’t mind my input, move that up forward on the upper receiver. It will help with acquiring target with both eyes open and a possibility to help your sight picture.

Best not to try to figure out government service. It might break you. Trust me. Enjoy that thing and as always....pictures please

I will say it again, why? Your 16” will get you to 800 yds. We want to educate you, not change your mind.

Same.

Do you plan on changing the whole thing to a carbine recoil system? You absolutely cannot just drop a carbine buffer in.

More than words would be had...

I can break anything..... lol, sorry, I tried to do something nice and look what happened

No, there is a lot of info here on that. The hazing comes from new members such as yourself joining and not reading up on posts here or asking questions that are difficult to answer without all the information we need to properly answer. This place is like the biker bar strangers see on the side of the road. Salty and scary dudes dwell with in. You open the doors and they all stare. You approach the bar and order your favorite libation and take a seat. You then over hear several conversations you have surprising interest in. You approach to join in and are met with apprehension. If you stay you’ll be accepted as long as you respect the rules and mind your manors. Drink to much and get out of hand and you’ll be helped out the door.

Can you take a pic of the gas tube in the can cut out from the bottom looking in? Should be in the middle of the cut out. And for shits and giggles, complete measurements of your recoil system please

This. These are a no go. The soft point will get marred and/or hang up on the feed ramp. DO NOT LUBE FEED RAMPS! Adding lube near the camber is not a good idea. The bolt, bcg, inside of the upper should have a healthy dose of lube. Lightly lube the inside of the extension. The larger AR’s need some break in to really get things going. The ramps could use a small amount filing/polishing, the scratches are a bit aggressive but not alarming overall. Get some more factory ammo, put rounds down range, and keep her wet

Dammit Doc... I grabbed the same. Plus 10 pmags, some magpul glock mags and a couple more CMC Powermags, which I was going get more but I must’ve cleaned them out myself. Can you 65b yourself?

As far as compatibility you are correct. Some companies products won’t play well with others, others will but cosmetically won’t match. We often suggest if at all possible by an upper an lower from the same company to avoid tolerance stacking issues. With luck, the upper you choose will fit, and all will be well. I suggest if you can, after milling your lower test fit a couple different brands of uppers if at all possible. There is no spec for the 308AR, so every manufacturer does their own thing.The 16” barrel is the right choice, much easier and lighter. Plus the closer to you the weight is the lighter it will feel. welcome

The best beer I’ve had in a very long time, and that is saying something!!! My buddy’s new brewery in a colander with a bigger local brewery, resulting that good good!!!! I'm going to try to get a couple more and maybe send out care packages to my two beer buds if I can get some.

Dang it, you beat me to it

Start with details of recoil system please, my money is that is the culprit

If that is your buffer measurement it’s off. Also don’t shoot soft point ammo in any AR with expectations of proper feeding. The feed ramps will catch the soft end of the projectile and cause you issues. If you’re going to hunt with them your better off hand loading into the chamber.

This guy knows his stuff, and at the very least, the two of you can shoot off and get a few mils. (Inside joke here, not at your expense). Your buffer appears correct but no your receiver extension. (Buffer tube) That should have a measured internal depth of 7” for that buffer.

This. To me not knowing your parts manual I’d start with recoil system. Just by your description it sounds like it is most likely incorrect.

I think your idea of mil spec is off. It has absolutely nothing to do with running in any condition. Also, you seem to have the belief that these guns are made of sugar and can’t get wet or dirty and if they do they won’t work. AK’s aren’t that much more reliable than modern AR’s and there are plenty of tests to prove it. That misconception has been long ago proven. The SCS is best meant for race guns and what most mean by that is a gun that uses one ammo tuned by the end user for competition. If you truly want a “SHTF” gun then you are building something that will shoot any given ammo and cycle properly without changing parts or tuning on the fly. That’s why we are giving you recommendations based on your verbage. Again, just a bunch of salty trigger pullers with experience. Mil spec is a specification of machining tolerances, not a requirement of performance capability.

You’re good, it was just a statement. Many come here with internet knowledge but not much practical and refuse the information we try to give them. You’ll be fine here. We will help you get sorted and out to the range.

No worries, it just clears up restrictions and what we can advise.

Also. Many here have trigger time and give answers based on that. Calculators and internet logic are fine until it’s not. 98z5v has the most of all of us and he and Matt Cross have both taught some great classes at a top secret facility which were proven on afterward on the range.