AngelDeVille

I haven't seen one where the BCG/buffer went back too far, I learned sumthin' new. Damn me for using mil-spec parts!

Buffer detent hole in the receiver is set too far back.

I love it! read my sig line.....

I have narrowed my search to this one ^^^^^

Nice progression! Your next task is to build two more rifles and optimize the load and oal for all three rifles. Start......... NOW! :banana: :banana: :banana:

He may have been talking about another brand of set he sells that was DPMS pattern, so I could easily be mistaken.

I have a size 13 I'll lend to the cause.

Call Chris Reideman to confirm what you have, good guy to talk to. Mine uses an AR10 barrel nut, and a modified AR10B bolt catch. My barrel and BCG are both DPMS pattern. (Anderson I think) I think there are two variations in the Matrix sets, I think the newer are all DPMS pattern, but don't quote me on that. I'm super happy with my "blem". I came out just under 1k on my build (glass not included). Two seconds with a sharpie fixed my blem. http://www.centralfloridafirearms.com From my learning here, the bolt carrier is interchangeable, it's just the bolt that needs to match the barrel pattern.

Just so you know I was implying Chase is a big female cat for not just slapping it on with a single pin spanner...... I just didn't feel I had been here long enough to just come out and say it..... :p The end results are pretty cool though.... ;) Big female cat...

Ok, more than a little PO'd right now, it took 10 days from the time I placed my Ares Armor order to the time of its arrival, and I was ok with that. (3 days to ship, 7 to arrive, less than a 900 mile trip) So my barrel, BCG, and gas tube arrive today and I'm getting ready to install it on my upper and I inspect the bore, and there's a lump of something in there. It looks like a lump of coating. I run a brush several times, and it doesn't budge. So I call customer service and they want to send a return label, have me send it back, and after they receive the return, then send me my replacement. So if turn-around remains constant I'm looking at 30 days from order placement to final assembly. I did point this out, and the replacement is being sent WITH the return label, but under threat that I'd be charged for both if the other doesn't arrive. I know I have heard a lot of good things about them on here, but right now I'm not too terribly happy.

A scout or socom16 would be on my list, but another AR10 may take its place.

My 1911 info link just has the Colt logo. ..

A cheap $10 extended latch off fleabay will work. I like the square one with an "X". Nice mount, is that an American Defense? What model?

The biggest limiting factor in length is the magazine. IIRC, both my lancer and magpuls max at about 2.82. Seat too short and your accuracy degrades because the bullet has to jump to the lands of the rifle. Also too short can reduce feeding reliability AND increase chamber pressure. Too long and not having enough jump to the rifle lands will increase pressure.

I pulled a few 180's for 300 BLK and .308 use... Powder for .308 too. Only 8 more tins to go....

Those look cool

Well I formed up 30+ cases of 300 BLK, the big hitch in the whole thing was the crappy Lee trimmer. Other than that it was pretty easy. I need to pull some more bullets before I load up some.

That's a well built lady, but I lost interest when she started talking... And turned off the video when she started loading her "clip".

Here is my PA scope with ultra high Warnes, and the Matech rear. I don't have any magpuls to measure but the Matech is .605" off the rail at the wings and .755 at the elevation adjustment.

He's building a 1911 that shoots .556, .762 and .45 acp. Without changing barrels OR magazines!

His boyfriend would have lots to look at.

You got a scope! I didn't get no fukkin' scope! I totally got shafted!

Do they have a "wandering zero"?

My Armalite AR-24 takes small frame EEA mags, CZ75b mags, and with the above mentioned notch mods beretta M9 mags fit.

The turrets on my PA ACSS are very crisp. Other than the weight I'm super happy with the optics and reticle. The 3-9 Nikon p223 bdc I just got has some mushy clicks, but they are definable. Still waiting on my rings to try it out.