Belt Fed Posted July 7, 2021 Report Share Posted July 7, 2021 On 7/7/2021 at 3:19 AM, Belt Fed said: Hmmmm, coulda been your problem. Expand But probably not and it probably will be a jam nachine. I feel bad for you and will give you 500 for a non working gun right now. Quote Link to comment Share on other sites More sharing options...
Lonewolf McQuade Posted July 7, 2021 Author Report Share Posted July 7, 2021 On 7/7/2021 at 3:20 AM, Belt Fed said: But probably not and it probably will be a jam nachine. I feel bad for you and will give you 500 for a non working gun right now. Expand 😂🤣😃 Well, not sure if it was copper or brass but there were 2 decent size chunks smooshed inside the chamber. Let some solvent soak & wire brushed it. Meh, didn't work. Then used a nylon brush & some Iosso paste & scrubbed the fuk out of it. THAT WORKED! Not sure if that was the issue, but damn sure it wasn't good . Gonna get out Saturday & see. Quote Link to comment Share on other sites More sharing options...
98Z5V Posted July 7, 2021 Report Share Posted July 7, 2021 On 7/6/2021 at 4:12 PM, Belt Fed said: Murderer Expand WAY worse than you and HogZilla, right?... Quote Link to comment Share on other sites More sharing options...
Lonewolf McQuade Posted July 7, 2021 Author Report Share Posted July 7, 2021 On 7/7/2021 at 4:09 AM, 98Z5V said: WAY worse than you and HogZilla, right?... Expand 😂🤣 i forgot about that! What a geriatric hypocritical sumbitch!! Quote Link to comment Share on other sites More sharing options...
98Z5V Posted July 7, 2021 Report Share Posted July 7, 2021 On 7/7/2021 at 4:21 AM, Lonewolf McQuade said: 😂🤣 i forgot about that! What a geriatric hypocritical sumbitch!! Expand I got your back. I got his back, too - depends on where the discussion is going. I'm just trying to keep up the fight... Quote Link to comment Share on other sites More sharing options...
Lonewolf McQuade Posted July 7, 2021 Author Report Share Posted July 7, 2021 On 7/7/2021 at 4:25 AM, 98Z5V said: I got your back. I got his back, too - depends on where the discussion is going. I'm just trying to keep up the fight... Expand 😂😄😅 Much appreciated! Quote Link to comment Share on other sites More sharing options...
Belt Fed Posted July 7, 2021 Report Share Posted July 7, 2021 On 7/7/2021 at 4:21 AM, Lonewolf McQuade said: i forgot about that! Expand Early warning signs of dementia. Quote Link to comment Share on other sites More sharing options...
Belt Fed Posted July 7, 2021 Report Share Posted July 7, 2021 On 7/7/2021 at 4:09 AM, 98Z5V said: WAY worse than you and HogZilla, right?... Expand Well yeah, that was self defense and only one. he done killed a whole pasture full of the poor little creatures. the big bully. Quote Link to comment Share on other sites More sharing options...
58marine Posted July 7, 2021 Report Share Posted July 7, 2021 @Lonewolf McQuade Nice picture of the chamber. It looks a little rough. If the problem recurs maybe polishing the chamber could be your fix? Just a thought. Quote Link to comment Share on other sites More sharing options...
Lonewolf McQuade Posted July 7, 2021 Author Report Share Posted July 7, 2021 On 7/7/2021 at 11:39 AM, 58marine said: @Lonewolf McQuade Nice picture of the chamber. It looks a little rough. If the problem recurs maybe polishing the chamber could be your fix? Just a thought. Expand Thanks. I noticed the tooling marks, wasn't sure if it was that rough or just over pronounced from the magnified close up pic. Quote Link to comment Share on other sites More sharing options...
Lonewolf McQuade Posted July 7, 2021 Author Report Share Posted July 7, 2021 On 7/7/2021 at 11:03 AM, Belt Fed said: Early warning signs of dementia. Expand What the Hell ever Frank!! Eer, Bob?..I mean Larry. Dammit, who ever you are Quote Link to comment Share on other sites More sharing options...
58marine Posted July 7, 2021 Report Share Posted July 7, 2021 Yeah. Someone more knowledgeable than us might be along soon. Quote Link to comment Share on other sites More sharing options...
Lonewolf McQuade Posted July 7, 2021 Author Report Share Posted July 7, 2021 On 7/7/2021 at 1:20 PM, 58marine said: Yeah. Someone more knowledgeable than us might be along soon. Expand So hold off with the 80 grit paper and high speed drill? 🤣 Quote Link to comment Share on other sites More sharing options...
58marine Posted July 7, 2021 Report Share Posted July 7, 2021 On 7/7/2021 at 1:33 PM, Lonewolf McQuade said: So hold off with the 80 grit paper and high speed drill? 🤣 Expand You could give it a try. If it don't work out @Belt Fed might still be willing to take it off your hands. Quote Link to comment Share on other sites More sharing options...
BigNate Posted July 7, 2021 Report Share Posted July 7, 2021 Long snout die grinder and a carbide burr should get it done… Quote Link to comment Share on other sites More sharing options...
58marine Posted July 7, 2021 Report Share Posted July 7, 2021 On 7/7/2021 at 1:42 PM, BigNate said: Long snout die grinder and a carbide burr should get it done… Expand @Lonewolf McQuade See, I told you someone more knowledgeable will be along soon. 🤣 Quote Link to comment Share on other sites More sharing options...
Lonewolf McQuade Posted July 7, 2021 Author Report Share Posted July 7, 2021 On 7/7/2021 at 1:41 PM, 58marine said: You could give it a try. If it don't work out @Belt Fed might still be willing to take it off your hands. Expand You mean once I have it all egged out to about a 300 Magnum new chamber? LOL Quote Link to comment Share on other sites More sharing options...
Lonewolf McQuade Posted July 7, 2021 Author Report Share Posted July 7, 2021 On 7/7/2021 at 1:42 PM, BigNate said: Long snout die grinder and a carbide burr should get it done… Expand 👍 Quote Link to comment Share on other sites More sharing options...
58marine Posted July 7, 2021 Report Share Posted July 7, 2021 On 7/7/2021 at 1:52 PM, Lonewolf McQuade said: You mean once I have it all egged out to about a 300 Magnum new chamber? LOL Expand Where's the " beer" button? Quote Link to comment Share on other sites More sharing options...
Lonewolf McQuade Posted July 7, 2021 Author Report Share Posted July 7, 2021 On 7/7/2021 at 1:56 PM, 58marine said: Where's the " beer" button? Expand No button here Send keg to: C/O Lonewolf McQuade 30-06 Firing Range Lane Itsascam Pa 54321 Quote Link to comment Share on other sites More sharing options...
58marine Posted July 7, 2021 Report Share Posted July 7, 2021 On 7/7/2021 at 2:21 PM, Lonewolf McQuade said: Send keg to: C/O Lonewolf McQuade 30-06 Firing Range Lane Itsascam Pa 54321 Expand Ok. Keg is on its way. Quote Link to comment Share on other sites More sharing options...
Lonewolf McQuade Posted July 7, 2021 Author Report Share Posted July 7, 2021 (edited) Garrett from Armalite returned my call today. Gave him all the details I could. The brass chunks in the chamber obviously could cause problems, along with the carbon marks from possibly gas seeping by, lateral markings etc. I also told him the chamber looked a little rough. He suggested checking the feed ramp for burr, polish if I find any. Also to get a chamber hone to smooth out the chamber. Edited July 7, 2021 by Lonewolf McQuade Quote Link to comment Share on other sites More sharing options...
Lonewolf McQuade Posted July 7, 2021 Author Report Share Posted July 7, 2021 On 7/7/2021 at 4:36 PM, 58marine said: Ok. Keg is on its way. Expand 🤣😂 Quote Link to comment Share on other sites More sharing options...
jtallen83 Posted July 7, 2021 Report Share Posted July 7, 2021 On 7/7/2021 at 4:41 PM, Lonewolf McQuade said: Also to get a chamber hone Expand Try some Flitz on a chamber mop in a drill before you spend big bucks. Worked for me once and others have said the same. Some use a dremel on sharp edges around the feed ramp, I've gotten by with a set of swiss needle files. Quote Link to comment Share on other sites More sharing options...
Lonewolf McQuade Posted July 7, 2021 Author Report Share Posted July 7, 2021 On 7/7/2021 at 5:19 PM, jtallen83 said: Try some Flitz on a chamber mop in a drill before you spend big bucks. Worked for me once and others have said the same. Some use a dremel on sharp edges around the feed ramp, I've gotten by with a set of swiss needle files. Expand Thanks @jtallen83 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.