shooterrex

More important than looks is how is the receiver fit in the stock. I'm betting the Magpul stock has a better bedding system for the receiver. I don't remember the chassis I'm using but the receiver fits tight.

https://www.righttobear.com/6-5-Grendel-Bolt-Completion-Kit-MPI-p/65gren-9310-kit.htm

Michigan. Looks like a mitten on the map.

For $15+ tax I bought one too.

Welcome from KY

The BCG will work fine even if the upper doesn't have a forward assist installed. Most of my builds have no forward assist. I just use a plug in the fa hole.

If I remember correctly both of mine were 11 1/8"

I would go with a regular spring and buffer in place of the silent captured stuff. Most people who have tried those do not have good luck getting their rifles to run till those are replaced with standard parts.

Mine are here today as well.

Shine a flashlight down the gas tube. Then look at the gas port.

https://www.armalite.com/SACItem.aspx?Item=AR10REKIT01&ReturnURL=/Armalite/Product-Category/AR10-Parts-Accessories/Lower-Receiver-Parts&Category=ac614400-ff09-4cdf-9d35-419a654e7201 This one right here for a carbine set up. They also have a set up for a fixed stock if that's what you want. Most of the difference between DPMS and Armalite pattern guns is the receivers.

Italian sausage, pepperoni, and pineapple is my usual pizza order.

You might only change 1 thing at a time. How do you know if something is screwing up, what it is if you change more than 1 thing at a time.

Wolf Grendel from sgammo. They have a little bit of 500 rnd cases.

Welcome from KY. You will find there is no standard for the large frame AR's. Reaserch and ask questions before you order parts. It will save headaches and buying parts that don't work well with other parts .

This will work for a recoil system. https://www.armalite.com/SACItem.aspx?Item=AR10REKIT01&ReturnURL=/Armalite/Product-Category/AR10-Parts-Accessories/Lower-Receiver-Parts&Category=ac614400-ff09-4cdf-9d35-419a654e7201

Good lookin pup.

Flitz or JB bore paste. The hone is probably overkill.

Welcome from KY.

Welcome from KY.

Ordered 2. BTW they moved to Montana. Got the h3ll out of Washington state.

The extractor yes just push the pin through. The ejector take 2 45acp cases. Put 1 on the tail of the bolt. Put 1 on the face of the bolt w/the head of the case against the ejector and clamp the whole thing in a vise. The cases keep everything from getting screwed up. You will need to drive the pin holding the ejector out w/a punch. An extra set of hands would help.

This is the ejector I went with. https://www.kakindustry.com/kak-bcg-ejector-308 The also sell extractors and you need a new one.

You had a carbine stock listed. That's why I suggested the carbine buffer set up from Armalite. They just work. A 308 rifle length gas tube is longer than an AR-15 rifle length gas tube. Nothing is milspec about the larger frame guns. There are tons of threads here proving this with builds not working till parts are changed so everything works together. Unless you are going to suppress the rifle you don't really need the adjustable gas block either. Building these large frame guns is fun but there is a learning curve.

Welcome from KY. I would suggest this recoil system in place of what you have listed. https://www.armalite.com/SACItem.aspx?Item=AR10REKIT01&ReturnURL=/Armalite/Product-Category/AR10-Parts-Accessories/Lower-Receiver-Parts&Category=ac614400-ff09-4cdf-9d35-419a654e7201 Tried and true recoil parts that work.