mrraley Posted August 13, 2015 Report Posted August 13, 2015 Who's got em? What changes have you made? What holster do you use?
MikedaddyH Posted August 13, 2015 Report Posted August 13, 2015 Stock holster,paddle holster outside the waistband, nylon vest holster and nylon underarm shoulder holster. Very large selection to choose from. Polished the ramp and added a LaserMax guiderod Laser. Powder River sells a spring kit but haven't got it ,also has à trigger kit.
blue109 Posted August 13, 2015 Report Posted August 13, 2015 Had one and liked it a lot. Xd gear holster works fine but I like serpas personally. Had a galco IWB I didn't like much. Didn't need any modifications. If my walther wasn't so spectacular I'd probably be carrying one.
Toolndie7 Posted August 13, 2015 Report Posted August 13, 2015 Been carrying it for about 6months. Toatlly diassembled it and "cleaned up" some of the parts. Put a set of speed sights on it and a pearce mag ext to get the pinky on it. I carry it IWB in a crossbreed minituck.
Robocop1051 Posted August 13, 2015 Report Posted August 13, 2015 XDs 9mm 3.3 here. In my personal opinion, this is the greatest defensive carry pistol on the market. • 9mm • low profile, single stack frame • 7/9 rounds • striker fired • fiber optic front sight The finger extension on the mag will always make it place higher than the G43. Still using the original paddle holster. Perhaps a G-code in the future.
Robocop1051 Posted August 13, 2015 Report Posted August 13, 2015 I have to admit... my Walther PPK/s gets a lot more attention just because it's a Walther PPK/s.
blue109 Posted August 13, 2015 Report Posted August 13, 2015 I want a ppk...but the PPS is my perfect concealment gun. I wear it everywhere in a IWB. Hospitals, bars, mall, my daughter's school...never worry about it being spotted.
mrraley Posted August 13, 2015 Author Report Posted August 13, 2015 A friend has the Alien gear IWB for it and swears it's better than Crossbreed. http://aliengearholsters.com Not a bad price either. I do want to put different sights on it, just not sure what though.
survivalshop Posted August 13, 2015 Report Posted August 13, 2015 (edited) I have four , XDM ,5" 45 acp , XDM 9mm 5", XDM 9mm 3.3" & an XD 4" in 45 acp , all have the Paddle holsters ,but am looking at a Tauga holsters for carrie . Made here in Florida . Edited August 28, 2015 by survivalshop
survivalshop Posted August 13, 2015 Report Posted August 13, 2015 I want a ppk...but the PPS is my perfect concealment gun. I wear it everywhere in a IWB. Hospitals, bars, mall, my daughter's school...never worry about it being spotted. Is the PPS in 380 ?
blue109 Posted August 13, 2015 Report Posted August 13, 2015 (edited) 9mm. Its pretty thin though. I run it 6+1 with the 8rd mag in a snag mag holder in my pocket. Have a K-holster (similar to supertuck) And wear it slightly to the rear. Completely comfortable and it fits my body shape in that position so it's pretty much invisible. Edited August 13, 2015 by blue109
mrraley Posted August 13, 2015 Author Report Posted August 13, 2015 While looking around, I like the way the speed sight look and would like to try a set before dropping any coin on them. www.speedsights.com
Toolndie7 Posted August 13, 2015 Report Posted August 13, 2015 (edited) While looking around, I like the way the speed sight look and would like to try a set before dropping any coin on them. www.speedsights.com I have no regrets about them. They are funny looking at first but Its all about that front sight. Put that point where you want it and its there <thumbsup> Edited August 13, 2015 by Toolndie7
mrraley Posted August 13, 2015 Author Report Posted August 13, 2015 I have no regrets about them. They are funny looking at first but Its all about that front sight. Put that point where you want it and its there <thumbsup> That's what I like to hear... time to save my pennies and get them then.
shepp Posted August 13, 2015 Report Posted August 13, 2015 I've got one in 45 its stock, have a Cleveland itwb holster (made here in Wisconsin). After seeing those sight I think those are going on there
Toolndie7 Posted August 13, 2015 Report Posted August 13, 2015 Is POA at the tip or at the center dot? At the tip. In the sunlight this green is crazy bright.
survivalshop Posted August 13, 2015 Report Posted August 13, 2015 I've been wanting a Sight removal tool to do sights , The good ones are on the big $$ side & you need a good one for the XD sights . I like this sights .
Toolndie7 Posted August 13, 2015 Report Posted August 13, 2015 I've been wanting a Sight removal tool to do sights , The good ones are on the big $$ side & you need a good one for the XD sights . I like this sights . Drifted the old sights out with the slide in a vise. Rear sight went right in ok, front sight was a bitch, stoned the sight a little and pounded it in.
shepp Posted August 13, 2015 Report Posted August 13, 2015 Tool is that a different bottom plate on your mag? How do you like it
Toolndie7 Posted August 14, 2015 Report Posted August 14, 2015 Tool is that a different bottom plate on your mag? How do you like it Make a big difference, I like it so far. http://www.pearcegrip.com/Products/Springfield%20Armory/PG-XDS
sketch Posted August 14, 2015 Report Posted August 14, 2015 Gotta say I just installed the speed sights (gunsmith with tools) and they are the cats pajamas ! Won't see the range untill next month !? I've herd some real reviews on these sights used out of country and front sight made the difference between life and death!
98Z5V Posted August 16, 2015 Report Posted August 16, 2015 (edited) I do want to put different sights on it, just not sure what though. i'm sure this isn't a problem for you, Pat, but... if you buy your sights from here: http://www.shop.xd-hs2000.com/Meprolight-Night-Sight-for-the-XD-Pistol-MAK11410.htm You just send him your slide, and he installs them for free. The XD sights are notoriously a damn bitch to change, because they're tight as hell. He does it for you. When mine came back, it was dead-nuts centermass on-target at 25 yards. Point Of Aim IS Point Of Impact. He nailed the installation perfect. Me: XD-45 LE Service Model (LE has the thumb safety) with a Springer Precision trigger kit, Springer Precision extended mag release, Meprolight tritium sights, and Streamlight TLR-4 light/laser combo. During the day, without light, it rides in a Mernickle PS6 High-Ride concealment holster. Waiting on a custom kydex holster to use when the light is on it, and that's coming from these guys: http://www.kt-mech.com/ Also rocking the XDs45 since it first came out, and it just runs in the XD gear holster that came with it. It has the Powder River Precision trigger kit, extended mag release, and extended grip safety. Very satisfied with this little bastard. Edited August 16, 2015 by 98Z5V
jtallen83 Posted August 16, 2015 Report Posted August 16, 2015 (edited) Great link for the sights Brother :hethan: he does Sigs as well! :2nd: Edited August 16, 2015 by jtallen83
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now