shooterrex
-
Posts
3,357 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Gallery
Store
Everything posted by shooterrex
-
Welcome from KY
-
I have a couple of mbt's in the parts bin if LaRue is out.
-
Are you going to owe doc another trigger???
-
Tennessee Arms compatable .308 magazine??
shooterrex replied to Mark123's topic in Building a .308AR
Pro mags for the most.part SUCK. Magpul Lr308/SR25 are good to go for DPMS Gen 1. -
What do you have on order or in the mail? Part 2
shooterrex replied to imschur's topic in General Discussion
Glock 17 slide and internals. Lower parts kit for 80% lower. Still waiting for the spring that holds the takedown lever in on my g23 build. Damn thing is here somewhere but I can't find it. Those little springs are out of stock almost everywhere. More Grendel mags and Glock mags for the 2new pistols.
-
Was going to buy some more Grendel ammo on Gunbroker. The American Gunner Grendel ammo I paid $139.00 for 200 rnds last spring got to over $3.00 a round on an auction. NO THANKS. Don't need it that bad.
-
-
The PSA bcg,'s are dpms pattern. Ballistic Advantage barrel fit in my PSA upper just fine. Rail was dpms high from local gun store. Yes Aero is easier to find stuff that works. The PSA upper will probably only fit a PSA lower.
-
We convoyed from Ft Bliss to Ft Hood once. Two day at 50mph each way.
-
Glad you got it running right. I think the only thing on my PSA that is still original is the upper and lower receiver and take down pins. And the bolt carrier group but it has a different ejector now.
-
Also check the ejector face. Is it square or rounded ? My creedmoor had to have a rounded ejector before it would run right. https://www.kakindustry.com/lr-308-parts/308-upper-parts/308-bcg-and-spare-parts/kak-bcg-ejector-308
-
Just use whatever recoil system and stock you prefer. The uppers barrel length has nothing to do with the stock configuration as long as the gas port and tube are set up properly.
-
The PSA barrel should be fine. You will need a dpms pattern BCG. You will need to check the gas system for length of gas tube and port size.
-
Double check the internal depth of your buffer tube 8" sounds like an odd measurement. Ar15's are 7" and Armalite's carbine buffer tube is 7 5/8".
-
https://www.amazon.com/TGOOD-Flag-fornicate-Decorations-Farmhouse-Resistant/dp/B08MXSGFRS/ref=trb_chk_auth?tag=forum03f-20
-
-
Unless you are going to suppress it you don't need an adjustable gas block. Just get the rifle running right and tighten everything down good and tight and be done with it.
-
I dimpled the barrel for the gas block then just snugged up the set screws. If you want a thread locker on the gas block use Rock Set. Locktite will loosen with heat and the gas block gets hot.I have reused gas tube pins getting them out just requires the proper roll pin punch.
-
Welcome from KY.
-
Good news! Any kind of cancer SUCKS.
-
Welcome from KY.
-
My buddy Dutch's. If you are coming to the Knob Creek machine gun shoot sometime I'll make sure he brings it along.
-
What else can cause my rifle to jump when fired?
shooterrex replied to 1survivor1's topic in Rock River Arms LAR-8
You might try a heavier buffer or stronger recoil spring. -
At my buddy Dutches house. He is a class 3 dealer and manufacturer. We were talking about the 40mm pump grenade launcher a while back. Here are pics of the 1 he has.
-
@Magwa
